Pantech Solutions. Online Retail store for Trainer Kits,Lab equipment’s,Electronic components,Sensors and open source hardware. This process is to assist in the repair of your Pantec receiver. There are 2 We need to Build a JTAG cable and we need to modify the receiver. To modify the. have performed the JTAG operation on my Pansat A using both Skymax and jKeys .. The first thing to do here is figure out if you have a PanTec MX or MS.

Author: Shaktik Vizshura
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Video
Published (Last): 23 November 2013
Pages: 281
PDF File Size: 19.75 Mb
ePub File Size: 18.36 Mb
ISBN: 118-3-44781-702-6
Downloads: 77842
Price: Free* [*Free Regsitration Required]
Uploader: Zulkimi

I would mount the board here as shown above. Turn off the receiver and disconect the JTAG cable and replace the cover and the 5 screws. Turn on the receiver. Once your comfortable with which pins, take a pen knife ;antec a thin blade or a razor knife and gently bend the pins closer together from half way between the chip and the board.

Locate the following tabs on your receiver If your machine is a MX go here. You can buy it separately but you will find it in a kit with everything you need. I did this for simplification. At the time of release, it wouldn’t make any difference.

Add the following to the end of the file Add application code to the project Step 5: Make the wires as short as possible and keep them organized.

A progress bar will appear. You will also require the 9 pin female to 9 pin female serial Straight through cable that came with your receiver. Study the picture below and familiarize your self with your receiver.


Make sure its firm then leave it alone. There jatg holes under these tabs filled with solder and this must be removed.

The air will quickly cool the board and help minimize trace burning. I used a meter and found the tab by the transister as shown below.

To make this easy we can cheat. I think cheaper is always better.

Pantec FTA Files & Pantec FTA KEYS

Now the good news is that the receiver isn’t dead Don’t touch anything until the completed box appears. You will know this if your LED’s don’t light or light properly. Try until you have success.

Your receiver will work at this point. You need the wires from pin 2,3,4,5,13,18,19,20,21,22,23,24, To program the Flash chip you will click on the Flash Programming button. How does cache work? We then have mtag clear the original flash on the receiver.

Remember to ground yourself before touching the board. When your satisfied that the parts are in the right spot, Push the leds into their appropriate holes in the case. The next part is the ground for the resister. Also make sure that you can place the board inside the box and put the lid on.

Switch Operation on a Local Network Example: There is no standard JTAG connector or pinout, so suppliers are able to define their own. That will let you know if you have your JTAG connected right. The next step is to flash the receiver using the serial cable that jtg with your receiver and the Pansat Loader v3.


Which jtag is best for pantec mx

You will get a dialog box like the one below. Expand copy the appropriate files to their directories. Load the Bin File. For the MS problem that may have been shutdown by the flashing of the unit with any pntec above auto-roll bin file read on. Generate Harmony Code Step 7: Analog Sensor Conditioning Additional content planned Please note mtag in the diagram above, it looks like the wires are connected in order.

Lab1 SD card Audio Player: Download the file to the receiver and wait until complete. Parts you will need: Use CPU double sided heat tape. You can cut the rest. Most of these boards are robotically created. Now confirm all connections and make sure you haven’t left anything inside the unit that could short.

For this step of the procedure, you will need the following parts. Now load the new bin. None of jhag is hard panfec you follow these steps exactly. Power up the unit and confirm that it still turns on and goes beyond the night rider stage. A full JTAG interface requires five pins.