ISO 7816-2 PDF

ISO 7816-2 PDF

ISO/IEC specifies the dimensions and locations for each of the contacts on an integrated circuit card of an ID-1 card type. It also provides. ISO describes the physical characteristics of smart chip cards. It includes accommodation of exposure limits for electromagnetic phenomena such as. ISO is one of most important standards in the smart card industry. Parts of ISO specify physical characteristics, dimensions and location of the.

Author: Bragis Dobar
Country: Uganda
Language: English (Spanish)
Genre: Environment
Published (Last): 24 June 2010
Pages: 492
PDF File Size: 1.97 Mb
ePub File Size: 11.50 Mb
ISBN: 545-2-72810-876-1
Downloads: 52892
Price: Free* [*Free Regsitration Required]
Uploader: Gomi

ISO/IEC 7816

ISO includes the commands for internal security management of the card and may include encryption techniques isl other security management methods. Newer chip fabrication technologies are moving sub micron, 0.

Leave this field empty. The RSC interface however defines two separate wires for data transmission and reception which would need hardware modification in order to interface with the single wire IC card directly.

Retrieved from ” https: The bending properties are tested by deflecting the card 78162 each axis as shown in figure 6.

The relative location ixo these components when present is shown in figure The format of a character frame is shown in figure The parity bit is defined to achieve even parity which means that the number of 1’s in the 8 data bits and the parity bit together results in an even number. Although the PC operates in full duplex mode. This page was last edited on 19 Aprilat Your email address will not be published.

Area 2 is provided for the cardholder identification data such as his name and address. This position is much closer to the longitudinal axis of the 7186-2.


Cancel reply Your email address will not be published. The three most widely used tests applied by fabricators are specified in the annex to the standard: In other projects Wikimedia Commons. This standard is in five parts and covers the specification of the magnetic stripe and the card embossing.

ISO/IEC – Wikipedia

It gives the 7816- name, description, format, coding and layout of each DE and defines the means of retrieval of DEs from the card. Created inupdated inamended inupdated in The power supply to the IC is defined to be between 4. Let us know what you have 78162 say: These characteristics fall into the following categories: The IC deactivation sequence for the interface device is as follows: This standard applies to the ID – 1 identification card specified in ISO and includes cards which may have embossing or magnetic stripes.

ISO standards by standard number. According to its abstract, it specifies the operating conditions of an integrated circuit card that provides a USB interface. With a periodicity of 30 bendings per minute the card is deflected to 2cm at its centre from the long ieo and 1cm from the short axis.

Although the integrated circuit could contain its own clock circuit for driving the internal logic, in practice most IC chips are supplied with an external clock by the oso device.

Data Layout on Magnetic Stripe Cards.

In effect it acts as a polarisation key and may be used to aid the correct insertion orientation of the card. This part specifies characteristics for a magnetic stripe, the encoding technique and coded character sets which are intended for machine reading.


It has to be said that this part of the isp could be improved and there is currently some work taking place in ISO on this very subject. Created inupdated inamended in As the title implies, this part of the standard specifies the location of embossed characters on an ID -1 card for which two areas are assigned. When the error condition is sensed then the transmitter should retransmit the erroneously received character. Further problems arose in deciding on iiso face of the card the connector should be located.

The ISO standard defines three reset modes, internal reset, active low reset and synchronous high active reset.

The asynchronous type of transmission is similar to that used by the serial RSC connector met on the personal computer. More particularly the slot for a card may include an extra indentation for the embossed area of the card. The electronic properties and transmission characteristics of the IC iiso are fundamental to interoperability.

These standards are well established so are the more important characteristics of a Smart Card which form the basis of the existing and emerging standards. The word occasional is defined to mean not more than four hours each time and not over times during ios life of the card.