BC558C DATASHEET PDF

BC558C DATASHEET PDF

BCC datasheet, BCC pdf, BCC data sheet, datasheet, data sheet, pdf, Boca Semiconductor Corporation, 30 V, PNP silicon planar epitaxial transistor. BCC Transistor Datasheet pdf, BCC Equivalent. Parameters and Characteristics. BC Silicon PNP Transistor. Audio Amplifier, Switch. Features: D Suitable for AF-Driver Stages and Low Power Output Stages. Absolute Maximum Ratings.

Author: Migul Vokinos
Country: Samoa
Language: English (Spanish)
Genre: Photos
Published (Last): 28 August 2008
Pages: 421
PDF File Size: 10.65 Mb
ePub File Size: 6.7 Mb
ISBN: 542-5-12236-731-2
Downloads: 91595
Price: Free* [*Free Regsitration Required]
Uploader: Taurg

A Transistors acts as an Amplifier when operating in Active Region. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. It is used in switching and amplifier applications.

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

It can amplify power, voltage and current at different configurations. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch datashfet Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. BC is a general purpose PNP transistor.

BC558 Datasheet, Equivalent, Cross Reference Search

BC is used in common emitter configuration for amplifiers. TL — Programmable Reference Cb558c. For amplification applications, the transistor is biased such that it is partly on for all input conditions.

  KABIR SAKHI SANGRAH PDF

Choosing Motor For Robots. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched.

The DC datashee gain varies in range to BC as switch When a transistor is used as a switch it is daasheet in the Saturation and Cut-Off Region as explained above. A resistor is always added in series with base pin to limit the base current. Skip to main content. The value of this resistor RB can be calculated using below formulae. This is known as the biasing.

In the absence of base signal, it gets completely off. What is Web Browser.

Interface SD Card with Arduino. The BC because of this large gain value is normally used to as a audio amplifier. It is also used as a complement datasneet transistors BC to BC Virgin Galactic — Commercial Space Flight.

BCC Datasheet(PDF) – Rectron Semiconductor

Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. SPI Module of Arduino. Arduino based GPS receiver. BC has a gain value of to ; this value determines the amplification capacity of the transistor. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

Amplifier modules like Audio amplifiers, signal Amplifier etc. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. The input signal at base is amplified and taken at the emitter.

  DEFINICION DE OTOTOXICIDAD PDF

Submitted by admin on 26 March In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. Complete Technical Details can be found in the BC datasheet given at the end of this page. The voltage divider is the commonly used biasing mode. This high-density System-in-Package SiP integrates controller, power switches, and support components.

BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

BC558C Datasheet

For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. Interface GPS with Arduino.

The transistor terminals require b5c58c fixed DC voltage to operate in the desired region of its characteristic curves. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. Choosing Battery for Robots.